Sugar Factory Tubes Sheet Ligaments

The ligament on a tube sheet is the material between two tube holes. In a perfect world the all the ligaments on a tube sheet will be exactly the sime size. However due to the variation in hole size due to tolerance and also due to mistakes in hole centre positioning there may be ligaments which are smaller than the theoretically calculated ligament. Now if it is found that on a particular tube sheet one or more of the ligaments is smaller than the others are we to reject the tube sheet and all the work done on it? If the tube sheet is rejected, the manufacturing programme will be delayed, and costs incurred.

The Tubular Exchanger Manufacturers Association (TEMA) has guidelines on minimum allowable ligaments on tube sheets. Unfortunately their recommendations only go up to 2 inch OD tubes, and so some extrapolation for 4 inch tubes is required.

tube dia [inch]	tube pitch [inch]			maximum hole diameter [inch]	nominal ligament [inch]	minimum permissible ligament [inch]
dt	p	p/dt	p-dt	dh	p-dh
0.250	0.313	1.250	0.063	0.259	0.054	0.025
0.250	0.375	1.500	0.125	0.259	0.116	0.060
0.375	0.500	1.330	0.125	0.384	0.116	0.060
0.375	0.531	1.420	0.156	0.384	0.147	0.075
0.500	0.625	1.250	0.125	0.510	0.115	0.060
0.500	0.656	1.310	0.156	0.510	0.146	0.075
0.500	0.688	1.380	0.188	0.510	0.178	0.090
0.625	0.781	1.250	0.156	0.635	0.146	0.075
0.625	0.813	1.300	0.188	0.635	0.178	0.090
0.625	0.875	1.400	0.250	0.635	0.240	0.120
0.750	0.938	1.250	0.188	0.760	0.178	0.090
0.750	1.000	1.330	0.250	0.760	0.240	0.120
0.750	1.063	1.420	0.313	0.760	0.303	0.150
0.750	1.125	1.500	0.375	0.760	0.365	0.185
0.875	1.094	1.25	0.219	0.885	0.209	0.105
0.875	1.125	1.290	0.250	0.885	0.240	0.120
0.875	1.188	1.360	0.313	0.885	0.303	0.150
0.875	1.250	1.430	0.375	0.885	0.365	0.185
1.000	1.250	1.250	0.250	1.012	0.238	0.120
1.000	1.313	1.310	0.313	1.012	0.301	0.150
1.000	1.375	1.380	0.375	1.012	0.363	0.185
1.250	1.563	1.250	0.313	1.264	0.299	0.150
1.500	1.875	1.250	0.375	1.518	0.357	0.180
2.000	2.500	1.250	0.500	2.022	0.478	0.250

Standard Ligaments

96% of ligaments shall be greater than

lig_std = p - d_h - (0.0032 t / d_t in + 0.030 in)

where t = tube sheet thickness

Minimum Permisible Ligament

No ligamant shall be less than

lig_min = -0.0010465 + 0.510467 · (p-d_h)

The factors in the above formula come from a linear regression of the data in the table above.

Example 1

In this example we consider a 2 in kestner evaporator type tube

tube plate thickness

t = 25 mm

tube outside diameter

d_t = 2 in
d_t = 50.8 mm

maximum tube hole dia

d_max = 51.48 mm

tube hole pitch

p = 70 mm

Drill drift tolerance

tol_dd = 0.0016 in · t / d_t
tol_dd = 0.02 in

standard ligament

l_std = p - d_max - (2 · tol_dd + 0.030 in)
l_std = 17.72 mm

minimum ligament

l_min = 0.0010465 mm + 0.5067383 · (p - d_max)
l_min = 9.38 mm

Example 2

In this example we consider a 4 in continuous vacuum pan type tube

tube plate thickness

t = 25 mm

tube outside diameter

d_t = 4 in
d_t = 101.6 mm

maximum tube hole dia

d_max = 102.63 mm

tube hole pitch

p = 120 mm

Drill drift tolerance

tol_dd = 0.0016 in · t / d_t
tol_dd = 0.01 in

standard ligament

l_std = p - d_max - (2 · tol_dd + 0.030 in)
l_std = 16.59 mm

minimum ligament

l_min = 0.0010465 mm + 0.5067383 · (p - d_max)
l_min = 8.78 mm

SUGAR PRICE

15 Dec 2008 White
$/tonne		319.50
15 Dec 2008 Raw
¢/lb		11.52